Seagate ST39103LC Technické informace Strana 53
- Strana / 132
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
df and du
Disk and volume information
3.4 Component Status
The ftsmaint ls command lists the components in the system and identifies any components that have been
removed from service. The list serves as a simple troubleshooting tool to verify that all the components are present and
shows their status (in/out of service). Refer to Section 2.6.3 to view a sample ftsmaint ls output screen.
3.4.1 Software State Information
The system creates a node for each hardware device that is either installed or listed in the /stand/ioconfig file.
The State field in the ftsmaint ls
display can show a hardware component to be in any one of the software
states shown in the following table.
State Meaning
UNCLAIMED
Initialization state, or hardware exists, and no software is associated with the node.
CLAIMED
The driver recognizes the device.
ERROR
The device is recognized, but it is in an error state.
NO_HW
The device at this hardware path is no longer responding.
SCAN
Transitional state that indicates the device is locked. A device is temporarily put in
the
SCAN state when it is being scanned by the ioscan or ftsmaint utilities.
The software state of a hardware component can change. For example, a component is initially created in the
UNCLAIMED state when it is detected at boot time. The component moves to the
CLAIMED state when it is recognized
and claimed by the appropriate driver. The transitions between the various software states are controlled by the
ioscan and ftsmaint utilities.
3.4.2 Hardware Status Information
In addition to a software state, each hardware component has a particular hardware status. The Status field in the
ftsmaint ls display can have any of the values shown in the following table.
Status Meaning
Online
The device is actively working.
Online Standby
The device is not logically active, but it is operational. Using the ftsmaint
switch
or ftsmaint sync command can be used to change the device
status to
Online.
Duplexed
The status is appended to the Online status to indicate that the device is
fully duplexed.
Fault Isolation
file:///H|/CSDoc/leotsg/section3.html (9 of 12) [01/12/2000 11:50:41 AM]
- PA-8500 Continuum Series 400 1
- Technical Service Guide 1
- CSD Homepage 4
- Suitcase 5
- PCI Card 5
- Flash Card 5
- Disk Drive 5
- Tape Drive 5
- 1. Introduction 9
- 1.3 Hardware Components 10
- 1.3.2 PCI Subsystem 11
- 1.3.3 Disk/Tape Subsystem 12
- 1.3.4 Power Subsystem 12
- 1.4 System Configurations 13
- 1.5 System Specifications 13
- 1.5.2 Environmental 14
- 1.5.3 Electrical 14
- 2. Operating and Maintenance 15
- Procedures 15
- 2.1.2 Manual System Startup 16
- 2.2 Shutting Down the System 17
- 2.3 Rebooting the System 18
- 2.4 Console Command Menu 19
- 0/2/3/0/4 22
- 0/2/3/0/5 22
- 0/2/3/0/6, 0/2/3/0/7 22
- /stand/ioconfig file 25
- SCAN state 26
- 2.7 Maintenance Procedures 29
- or 0/1) 30
- is the year 30
- 0/2/0/0.0 or 0/3/0/0.0) 32
- 0, 1, or 2) 34
- vgdisplay -v display 35
- 2.7.2 Maintaining Flash Cards 37
- 2.7.3 Burning PROM Code 39
- 0-9), cc is 40
- 0-99), V is 40
- for the standby 41
- 3. Fault Isolation 45
- 3.2. System Component LEDs 46
- 3.2.1 Power Supply LEDs 47
- 3.2.1.4 ACU Status LEDs 48
- 3.2.2 Disk Drives 49
- 3.2.3 Suitcase LEDs 50
- 3.2.3.2 Suitcase Status LEDs 50
- 3.2.4 PCI Cards 51
- and ioscan 52
- 3.4 Component Status 53
- 3.5 Fault Codes 54
- Fault Isolation 55
- 4.1 List of FRUs/DRUs 57
- 4.3 Power Removal 59
- 4.4 Access Doors 59
- Hardware Removal Procedures 60
- 5. Theory of Operation 96
- 5.1 Suitcase 97
- 5.1.1.2 Memory Module 99
- Theory of Operation 100
- 5.2 PCI Subsystem 101
- 5.2.1 PCI Bus 102
- 5.2.2 PCI Bridge Card 102
- Label Primary Bootloader 103
- - CONF (configuration file) 103
- HP_UX file on the flash card 104
- 5.2.3 PCI Adapter Cards 104
- ISO 4902 (V.36) 2.048 Mbps 106
- ISO 4903 (X.21) 2.048 Mbps 106
- V.35 2.048 Mbps 106
- 5.3 Disk Subsystem 108
- 5.3.1 Input DC Power 109
- 5.3.3 Disk Configurations 111
- 5.4.3 Power Specifications 115
- 5.5 Cooling Subsystem 116
- 6. Part Numbers 119
- 6.3 Power Subsystem 120
- 6.4 Cabinet 121
- Description FRU/CRU/DRU 122
- 6.6 Optional Equipment 123
- 7. Related Documentation 124
- 8. Upgrades 125
- 8.2.2 Upgrade Procedure 126
- Upgrades 127
- ID prom written and verified 129
- /Validate/Write/Exit? 129
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce